Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Don't take too lightly the forklift at work. If the operation is not good, there will be severe crashes in mins, and there are many accidents involving forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift motorist does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Case 7: The forklift driver did not put on a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale must be secure before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the pole must be slanted backward. .
2. Do not raise the fork expensive when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles in the sky. When the tons is taking a trip, the fork should not be increased expensive, which will impact the security of the forklift. .
3. After unloading, the fork ought to be reduced to the regular driving position before driving. .
4. When transforming, if there are pedestrians or lorries nearby, the driving signal ought to be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the lorry to lose lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with tons unless there are unique conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a particular safety distance from the vehicle in front. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be elevated other than when piling or packing. .
8. The elevation of the tons should not block the chauffeur's sight. In unique conditions, when the thing influences the forward vision, drive at a reduced speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The safe driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a balancing role. .
12. If troubles are located, they will be repaired and reported in a prompt way, and they will never ever run with health problems or conceal them.

filling and discharging.
1. When fork-loading items, the range between the two forks must be changed as required to make the tons of the two forks well balanced and not skewed, and one side of the thing must be against the shelf. .
2. It is forbidden to collaborate with a solitary fork or use a fork top or draw. In special conditions, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be braked with the brake. .
4. The rate of the car need to be sluggish and constant. Beware not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure people. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it ought to be kept in mind that the fork tip must not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the Stand-on Electric Pallet Stacker gantry to ensure that the lots does not slide backwards. The pole can be slanted ahead a little when the load is reduced Electric Forklift Truck for Warehouse to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard items with the fork head. .
7. When the forklift is functioning, it is restricted for individuals to stand around the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is forbidden to make use of forks to raise employees to engage in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water need to be included.
2. Examine the security performance of starting, running and stopping.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the exterior leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " totally free switching";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the vehicle must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or heavy items and go to the vehicle driver's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to raise the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same length as the challenge need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844